Bilge Filters

Wavestream Bilge System

A Development of World‐Wide Importance which prevents oily bilge water being pumped into the sea.
All types of boats risk polluting their surroundings when they pump out their bilges. Bilge water invariably contains fuel oil, lubricatng oil and grease which cannot be separated and is dumped into the seas and rivers of the world. Legislaton to prevent this operates in most parts of the world, and is being progressively tightened.
Wavestream ends this. Over the past seven years a new filtration system, based on XOil bonding technology, has been developed for the oil and shipping industries. XOil is a filter material which bonds with oil.
It is processed into sheet form and converted into simple filter cartridges which fit easily and neatly into the pipework from bilge pumps. So effective is XOil that each filter cartridge will absorb 3 times its own weight of oil. So efficient is XOil that even the smallest system will handle 40 litres per minute.

Wavestream Micro System

Designed for the bilges of day boats, RIBs and small sports boats or where minimal space is available, the Micro unit is easy to connect into the bilge water system, using ¾ “ BSP connections. The unit takes a space only 190mm high by 120mm diameter. Filter cartridges can be replaced in seconds.

Wavestream 1000 System

The 1000 system has a larger filter element to cope with the demands of larger pleasure boats up to 20m. ¾” BSP connections are used, and the flow rate, at 40 litres, is the same as the Micro system but filter cartridge replacement intervals double.

Wavestream 2000 System

Recommended for a large pleasure craft and commercial boats, the 2000 system will handle bilge pump flow rates up to 265 litres per minute with a 117mm diameter filter cartridge and 1 ½” BSP connections.

Wavestream 3000 System

The 3000 is designed for large commercial craft and ships. It incorporates a massive filter cartridge almost 500mm long, with significantly increased capacity. The flow rate and BSP connectors are common with the 2000 series.

Wavestream Stainless Steam

These multi-cartridge systems were born in the oil industry but can be used for even larger vessels than the 3000 system. Each unit is produced to meet a defined need. Details of the flow rates are needed to specify.

* All systems have Lloyds Approval

Filtration Systems

Wave International Ltd Filtration Systems
Main distributors for Wave International technically advanced marine filtration systems:

• Wavestream bilge filter systems
• Wavebrite waste water filter system
• Flostream drinking water filter system
• Prostream watermaker filter protection system
• Waveair holding tank vent filter system
• Waveshine wash & rinse system

Below is the Full Range of Wave International products. This can either be viewed in the window below (select the desired width) or, alternatively, click on the link underneath the window and this will open the Guide in the browser.

Wave Systems

Bilge Pumps

AR Peachment Ltd are suppliers of Jabsco & Rule Bilge Pumps.  A bilge pump needs to be efficient, reliable and easy to use.  In an emergency the bilge pump may be a lifesaver.  A fast pumping rate can gain time for other emergency actions.

Main features of these bilge pumps include:

  • Exclusive moisture tight seals.
  • Anti-airlock protection.
  • Compact, efficient, long life motors.
  • No burn-out when run dry.
  • Easy clean snap-lock strainer bases.
  • Stainless steel shafts.
  • Completely submersible.
  • Marine grade blocked wiring.
  • Rust & corrosion protection.
  • Silent & vibrationless operation.

Generally bilge pumps can be categorised into five main areas:

  1. Manual Diaphragm Pumps  – The traditional mainstay of small craft bilge pumping systems.
  2. Electric Submersible Pumps  – The most popular type of electric bilge pump.
  3. Electric Diaphragm Pumps – Excellent for shallow bilge boats.
  4. Electric Flexible Impeller Pumps – Flexible impeller pumps make excellent bilge pumps, principally because of their ability to handle bilge debris without damage.
  5. Engine Driven Flexible Impeller Pumps – Probably the strongest and most reliable pumps produced today.

Alternatively visit our Contact Page

Calorifiers

SureCal Calorifier

Surejust have been prominent in the marine industry for 25 years and have developed a range of calorifiers of the highest standard used by boat builders around the world!

SureCal boilers are made of the finest quality materials, which guaranteeing the ultimate performance and reliability. Inaddition,the drop coil technology and finned surface heat exchanger used in the boiler provides unrivaled heat recovery. The units also come in twin coil version for use with secondary water heaters. The unit is quick and easy to install with full fittinginstructions provided. The boiler is insulated in a polyurethane jacket which will retain the heat for up to 24 hours after the engine has been switched off. The boiler is made of 100% copper, this gives both performance and healthbenefits.

SureCal calorifiers come completely assembled ready for quick and easy installation. The immersion, pressure release valve, barbed engine coil connections and stainless-steel fixing brackets all come as standard. A thermostatic mixer valve is fitted as standard for the safety of those onboard and increases the volume of hot water available. The stored water within the boiler reaches the same temperature as the engine (generally 85°C). If the mixer valve is set at 65°C you will generally increase your available hot water supply by 25%. Every calorifer is also individually bench tested ensuring quality and reliability every time. In house development and a commitment to customer service, quality and reliability allow us to provide boat builders with the exact shape and size of boiler to suit their space and application.

Capacity (litres)Tank length no fittings (mm)Overall Length with fittings (mm)Diameter
(mm)
18550650274
329001000274
4512001300274

Click above image to expand

Click above image to expand

Sound Proofing

Noise Insulation Materials & Accessories

Main distributors for the Siderise proven range of high quality UK manufactured noise insulation materials.

A range of technically advanced noise insulation materials:

 

  • Compliant with the European Recreational Craft Directive
  • Standard sizes 12mm, 32mm, 45mm and 60mm
  • Range of tapes & accessories

Maritex

Sealglass

Reinforced Aluminium Foil

Noise Insulation Materials and Accessories

Siderise noise insulation uses high performance barrier materials to achieve excellent acoustic results with low frequency noise associated with diesel engines and other onboard noise generating equipment.

Technical Specification

  • Fire Safety – Materials available for RCD, MCA, and Class compliance
  • Class 0 fire rated surfaces (BS476-7)
  • All materials tested to ISO 4589-3 (oxygen index – elevated temperature)
  • Compliant to ISO 9094-2 Fire Protection for craft with a hull over 15m
  • Bulkhead performance up to Rw 54dB (EN ISO 717-1)
  • Fuel & oil resistant facing

Packing (12mm and 32mm materials):

12mm and 32mm (1/2” and 11/4”) materials are packed four sheets to a box.
Each sheet is 1000mm x 600mm (39” x 24”) making the total area 2.4 sq. metres (26 sq. ft.).
Box weight is approximately 14kgs for 12mm and 19kgs for 32mm.

Packing (45mm materials):

45mm (1 3/4”) materials are packed two sheets to each box.
Each sheet is 1000mm x 600mm (39” x 24”) making the total area 1.2 sq. metres (13 sq. ft.).
Box weight is approximately 16kgs.

Packing (60mm materials):

60mm (2 3/8”) materials are packed two sheets to each box.
Each sheet is 1000mm x 600mm (39” x 24”) making the total area 1.2 sq. metres (13 sq. ft.)
Box weight is approximately 11kg.

Actual noise attenuation achievable with the products is dependant on many factors relating to the specific installation. Please note the above graphs are indicative only.
Please contact Halyard for further information and detailed product specifications to suit your particular installation requirements.

For more information visit Halyard Website

If you require further information about this or any other product, please visit our Contact Page

Engine Mountings

Aquadrive Antivibration System

Aquadrive System Engine Mounts

Engine MountsWeight
50210 Series engine mounts complete with stud and any stiffness grade0.5kg
50220 Series engine mounts complete with stud and any stiffness grade1.1kg
50230 Series engine mounts complete with stud and any stiffness grade2.6kg
50240 Series engine mounts complete with stud and any stiffness grade9.5kg

It is essential to select the correct rubber grade and mount for the engine or generator in question. For reference, the chart above shows the level of deflection
(or squash) that will occur on each model of mount for a given loading.
In general you should aim for 3mm on the 50210, 4mm on the 50220, 5mm on the 50230 and 6mm on the 50240. The numbering system is simple: A 50223
mount is the 50220 model with number three rubber hardness and so on. Some engines, particularly those with less than four cylinders, require particular care and
your distributor will help with these.

Below is a comprehensive PDF from R & D Marine. This can either be viewed in the window below (select the desired width) or, alternatively, click on the link beneath the window and this will open the Guide in the browser.

Exhaust / Silencers

Exhaust Systems and Accessories

Watercooled or dry systems, standard or bespoke risers spray heads, silencers, separators, DPF & SCR aftertreatment solutions

Standard product range:

  • To suit exhaust systems from 38mm to
    203mm diameter
  • Extensive range of different shapes and sizes

Bespoke solutions:

  • Designed to meet customers requirements
  • Solutions to c. 4000hp
  • Spray rings to DN700
  • DPF & SCR solutions by Emigreen
  • Lloyd’s Type Approvals

Bespoke Risers and Spray Heads

The general make-up of a riser and spray head assembly is shown below.
Each system is designed and manufactured to suit the particular engine and engine room configuration. Supports and thermal jackets are normally suppliedas part of the installation kit.

PartsDescription
1Optional down angled spray head
2Spray head with water injection connection which is installed into the exhaust hose
3Curved stainless steel bend, used in the upper and lower sections
4Flange connector to suit engine turbo outlet
5Riser tube as required
6Flange connection
7Heat protective jackets
8Heat protective jacket for riser tube
9Support brackets as required

Composite Silencers and Separators

Lift Silencers – Top In Top Out

Drawings and dimensions are for guidance. Alternative sizes and configurations available on request. Reference numbers that end with B are not Lloyd’s approved.

Lift Silencers – Side In Top Out

Drawings and dimensions are for guidance. Alternative sizes and configurations available on request. Reference numbers that end with B are not Lloyd’s approved.

Lift Silencers – Side Angle In Top Out

Drawings and dimensions are for guidance. Alternative sizes and configurations available on request.

Lift Silencers – End In End Out

Drawings and dimensions are for guidance. Alternative sizes and configurations available on request.

In-line Round Body Silencers

Drawings and dimensions are for guidance. Alternative sizes and configurations available on request. All units are made to order and customisable.

In-line Oval Body Silencers

Dual Chamber Silencers

Combined Silencer / Separators

Drawings and dimensions are for guidance. Alternative sizes and configurations available on request. All units are made to order and customisable.

Below is the Full Range of Halyard products. This can either be viewed in the window below (select the desired width) or, alternatively, click on the link underneath the window and this will open the Guide in the browser.

Exhaust Systems