| 2200831 VHM 26 DTP + fittings | ||
|---|---|---|
| Maximum torque | 27 kpm | 200 ft.lbs |
| Stroke | 150 mm | 5 28/32″ |
| Maximum pressure | 50 bars | 725 PSI |
| Volume | 62.6 cc | 3.8 cu.in |
| Radius of tiller arm | 129 mm | 5 5/64″ |
| Total rudder angle | 70° | |
| Weight | 1 kg | 2.2 lbs |
| Dimension Drawing for 2200831 | ||
| Accessories for VHM 26 DTP | |
|---|---|
| 2201994 | Set of fittings for VHM 224 |
| 2200810 | Ø 6 mm flexible tube (per metre) |
| 2200803 | By-pass for Ø 6 mm flexible tube |
| 2200003 | Tiller arm LS 30 P + screws & bolts |
| 2200059 VHM 32 DTP | ||
|---|---|---|
| Maximum torque | 50 kpm | 361 ft.lbs |
| Stroke | 200 mm | 7 7/8″ |
| Maximum pressure | 50 bars | 725 PSI |
| Volume | 120.5 cc | 7.35 cu.in |
| Radius of tiller arm | 180 mm | 7 3/32″ |
| Total rudder angle | 70° | |
| Weight | 2.3 kg | 5.1 lbs |
| Dimension Drawing for 2200059 | ||
| Accessories for VHM 32 DTP | |
|---|---|
| 2200123 | Set of straight fittings 1/4 BSPP for Ø 8 mm flexible tube |
| 2200049 | Set of flexible tube and fittings 1/4 BSPP Ø 10 mm |
| 2200024 | Ø 8 mm flexible tube (per metre) |
| 2200027 | By-pass for Ø 8 mm flexible tube |
| 2200045 | By-pass Ø 10 mm inflexible tube |
| 2200060 | Tiller arm LS 50 P + screws & bolts |
For boats fitted with a rudder with speed not exceeding 25 knots, the torque of the rudder or rudders is calculated according to following formula and corrections.
It must be known that the torque necessary to manoeuvre a boat depends on:
C = Torque in kpm schema_safran
S = Total surface of rudder (H x Lg) in sq. m
H = Height of rudder in m
Lg = Width of rudder in m
Lc = Compensation width in m
V = Maximum speed of the boat in knots
K = Coefficient according to total angle of rudder
| Port to starboard | 70° | K = 15.89 |
| Port to starboard | 80° | K = 17.80 |
| Port to starboard | 90° | K = 19.52 |
| Corrections in function of the type of boat: | |
|---|---|
| For sailing-boats | C x 0.5 |
| For a boat with a steering nozzle | C x 2.0 |
| For twin engine power boats with 1 rudder | C x 0.5 |
| For boats fitted with several rudders (catamarans, trimarans, monohulls) | Multiply the calculated torque result by the number of rudders fitted on the boat |
Once the torque is known, the appropriate cylinder is selected and one or two manual pumps will be added.
Note: If the selected pump has a higher flow rate in order to reduce the number of turns lock to lock, it will be necessary to use a steering wheel with the maximum recommended diameter.
For pleasure boats with planing or semi-planing hulls and speed exceeding 25 knots, the cylinder may be selected by using the chart below:
| Length of Hull | Cylinder Type – 1 Rudder | Cylinder Type – 2 Rudders |
|---|---|---|
| 8 metres | VHM 40 DTP | VHM 32 DTP |
| 10 metres | VHM 40-254 | VHM 40 DTP |
| 12 metres | VHM 40-254 | VHM 40 DTP |
| 14 metres | VHM 50 DTP | VHM 40-254 |
| View or Download our Instruction Manuals and Catalogues here: | |
|---|---|
 | Catalogue Hydraulic Steering Systems for Outboard Motors |
 | NOT-100 Installation and Bleeding of LS Manual Helm Pumps.png |
 | NOT-200 Mounting and Bleeding LS Outboard Cylinders (Includes: VHM EX 75, 150 and 200 HP) |
 | NOT-210 Mounting and Bleeding LS Outboard Cylinders (Includes: VHM EX 80, 125, 175 and 225 HP) |
 | NOT-201 Mounting of LS Stern Drive Cylinders |
With this tiller for LS outboard cylinders, the boat can be steered from the motor.
Thanks to this function, the motor can easily be operated without having to resort to the steering wheel (for various fishing actions, anchorage, watch and emergency tiller if need be).
Equipped with a quick coupling, the tiller can be fitted and removed easily and stored in a locker.
Manufactured in stainless steel tube, its weight does not exceed 0.8 kg.
Do not use at a speed exceeding 6 knots.
| Tiller for Outboard Motor Cylinders: | |
|---|---|
 | 2204073 Dimension Drawing for 2204073 |
 | 2200803By-pass valve for flexible tube TS Ø6 mm 2202496By-pass valve for flexible tube TS Ø6 mm |
 | 2200027By-pass valve for flexible tube Ø8 mm + recoverable nozzle |
Cylinder type 28 ST HB AS is fitted directly on the power assisted steering system of the stern-drive motor. No additional mounting kit is required. It is suitable for Volvo, OMC, Mercruiser, Yamaha and others
| Kit Combination For Single Steering Station | |
|---|---|
| 2200950 | 1 Pump 30HB with lock valve |
| Dimension Drawing for 2200950 | |
| 2200358 | 1 Cylinder VHM 28 ST HB AS |
| Dimension Drawing for 2200358 | |
| 2200021 | 1 Set of pump fittings |
| 2200022 | 1 Set of cylinder fittings |
| 2200024 | x Metres of flexible tube Ø 8 |
| Kit Combination For Twin Steering Station | |
|---|---|
| 2200950 | 2 Pumps 30HB with lock valve |
| Dimension Drawing for 2200950 | |
| 2200358 | 1 Cylinder VHM 28 ST HB AS |
| Dimension Drawing for 2200358 | |
| 2200021 | 3 Sets of pump fittings |
| 2200022 | 1 Set of cylinder fittings |
| 2200047 | 1 Set of tees |
| 2200024 | x Metres of flexible tube Ø 8 |
These cylinders are fitted on in the same way as a cable steering system. Fittings and tubes are the same as for cylinder VHM 28 ST HB AS above (2200358).
| Cylinder Pump & Motor Selection: | Number of turns lock to lock in function of the Pump / Cylinder selection | Type motor / cylinder | |||
|---|---|---|---|---|---|
| 2200948 pump 26 HB LV | 2200950 pump 30 HB LV | 2201105 pump 35 HB LV | 2201107 pump 40 HB LV | (Other types on request) | |
| 2200546 cylinder VHM 28 ST HB DT Dimension Drawing for 2200546 | 4 | 3.6 | 3 | 2.6 | Up to 175 HP Motor VOLVO |
| 2200460 cylinder VHM 32 ST HBV DT Dimension Drawing for 2200460 | 5 | 4.5 | 3.7 | 3.2 | Up to 260 HP Motor VOLVO |
| 2200344 cylinder VHM 32 ST HBM DT Dimension Drawing for 2200344 | 4.7 | 4.2 | 3.5 | 3 | Up to 175 HP Motor MERCRUISER – OMC |
| Pumps for Stern Drive: | |
|---|---|
| 2200948 | Pump 26 HB with lock valve |
| 2200950 | Pump 30 HB with lock valve |
| 2201105 | Pump 35 HB with lock valve |
| 2201107 | Pump 40 HB with lock valve |
| Dimension Drawing 'All Above' | |
| Steering Kit Composed Of: | |
|---|---|
| 2200073 | 1 Pump 40 CT with lock valve |
| Weight | 4.1 kg |
| Dimension Drawing for 2200073 | |
| 2210000 | 2 “Race” cylinders 28 C 158 |
| Weight | 1.2 kg |
| Dimension Drawing for 2210000 | |
| OR | |
| 2210007 | 2 “Race” cylinders 32 ST 20 C 181 |
| Weight | 2.2 kg |
| Dimension Drawing for 2210007 | |
| 2200021 | 3 Sets of pump fittings |
| 2200023 | 2 Sets of cylinder fittings |
| 2210002 | 1 Distribution block |
| 2200024 | x metres of Ø 8 flexible tube |
| Steering Kit Composed Of: | |
|---|---|
| 2202068 | 1 pump 30-90 CT with lock valve |
| Weight | 7.5 kg |
| Dimension Drawing for 2202068 | |
| 2201976 | 2 s/steel cylinders 40 ST 28 C220 |
| Weight | 6.4 kg |
| Dimension Drawing for 2201976 | |
| 2200023 | 2 Sets of cylinder fittings |
| 2210002 | 1 Distribution block |
| 2200024 | x metres of Ø 8 flexible tube |
| + various fittings | |
 | 2200181 | Plastic Wheel |
 | 2200182 | Imitation Leather/Anodised Alu |
 | 2201143 | OB Filling kit |
 | 2201058 | Pump bezel |
 | 2201753 | Bulkhead strain relief |
 | 1206001 | S/steel motor connection plate for cylinder VHM EX 350 HP/3500 HP |
| 2203671 | Adapter Kit for Honda Motors (for cylinders VHM EX 125,175,225 HP) | |
 | 1206001 | HB 5 Tilt Pump |
 | 1206001 | Tie rods |
Depending on its implementation, the flange on a dual outlet pump makes it possible to:
Dual outlet pumps are supplied with two interchangeable blank plugs.
| 2203711 Pump 20 HB DS | ||
|---|---|---|
| Flow rate | 20 cc/t | 1.2 cu.in/rev |
| Minimum size of tubing | ∅ 6 mm | 25″ |
| Weight | 2.8 kg | 6.17 lbs |
| Volume | 400 cc | 24.4 cu.in |
| Maximum Wheel diameter | Ø 520 mm | 20 1/2″ |
| 2203712 Pump 26 HB DS | ||
|---|---|---|
| Flow rate | 26 cc/t | 1.6 cu.in/rev |
| Minimum size of tubing | 8×10 mm | .31x.39″ |
| Weight | 2.8 kg | 6.17 lbs |
| Volume | 400 cc | 24.4 cu.in |
| Maximum Wheel diameter | Ø 520 mm | 20 1/2″ |
| 2203712 Pump 30 HB DS | ||
|---|---|---|
| Flow rate | 29 cc/t | 1.7 cu.in/rev |
| Minimum size of tubing | 8×10 mm | .31x.39″ |
| Weight | 3.4 kg | 7.5 lbs |
| Volume | 400 cc | 24.4 cu.in |
| Maximum Wheel diameter | Ø 520 mm | 20 1/2″ |
| Dual Outlet Pump models 23 to 35 CT HB DS |
|---|
| Dual Outlet Pump models 23 to 35 CT HB DS Dimension Drawing |
| 2203708 Pump 23 CT HB DS | ||
|---|---|---|
| Flow rate | 23 cc/t | 1.4 cu.in/rev |
| Minimum size of tubing | 8×10 mm | .31x.39″ |
| Weight | 3.4 kg | 7.5 lbs |
| Volume | 400 cc | 24.4 cu.in |
| Maximum Wheel diameter | Ø 520 mm | 20 1/2″ |
| 2203709 Pump 29 CT HB DS | ||
|---|---|---|
| Flow rate | 29 cc/t | 1.7 cu.in/rev |
| Minimum size of tubing | 8×10 mm | .31x.39″ |
| Weight | 3.4 kg | 7.5 lbs |
| Volume | 400 cc | 24.4 cu.in |
| Maximum Wheel diameter | Ø 520 mm | 20 1/2″ |
| 2203710 Pump 35 CT HB DS | ||
|---|---|---|
| Flow rate | 35 cc/t | 2.14 cu.in/rev |
| Minimum size of tubing | 8×10 mm | .31x.39″ |
| Weight | 3.4 kg | 7.5 lbs |
| Volume | 400 cc | 24.4 cu.in |
| Maximum Wheel diameter | Ø 520 mm | 20 1/2″ |
This product – the only one of its kind – is the most compact system on the market.
The hydraulic pump has been integrated directly into the tilt mechanism and is fitted with a lock valve.
ORIENTATION CAPACITY
Possible orientation angle:
-24° to +24° (5 positions).
|
|---|
| Flow Rate | |
|---|---|
| 2203658 | HB 5 Tilt Pump – 20 CT 20 cc/t |
| 2203559 | HB 5 Tilt Pump – 26 CT 26 cc/t |
| 2203659 | HB 5 Tilt Pump – 30 CT 30 cc/t |
| 2203669 | HB 5 Tilt Pump – 35 CT 35 cc/t |
| 2203670 | HB 5 Tilt Pump – 40 CT 40 cc/t |
| 2203695 | HB 5 Tilt Pump – 50 CT 50 cc/t |
| HB 5 Tilt Pump |
|---|
| HB 5 Tilt Pump Dimension Drawing |
The design of this product allows for a very smooth steering feel.
The use of a brushless motor which is only activated when needed, ensures minimal noise generation and lower electric consumption.
The power pack integrates the autopilot functionality and is compatible with the various market players. Owing to its compact size and simplicity of installation, it can be adapted as an add-on to most existing hydraulic steering systems.
